Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.     

生物气溶胶的吸湿性

归纳了有关气溶胶吸湿性的测量方法以及过去近30a来文献中报道的生物气溶胶吸湿性的主要研究成果,总结了不同种类生物气溶胶之间吸湿性的差异.已有研究表明,绝大部分的生物气溶胶粒子都具有一定的吸湿性,当相对湿度为90%时,吸湿增长因子约为1.04（真菌孢子）~1.22（细菌）,花粉颗粒物吸湿后的质量与之前的比值为1.30~1.55.最后,提出了目前关于生物气溶胶吸湿性研究中尚未解决的科学问题及该领域的主要发展方向.     

铁基质强化新型功能性化粪池高效处理黑水的试验

以铁基质生物载体为核心,将物理、生物和化学方法结合,对化粪池进行功能强化,实现黑水的原位深度处理.探究了溶解氧（DO）和碳氮比（C/N）等因素对黑水中污染物降解的影响,并在最佳运行参数下考察了氮素在系统中的转化机制.结果表明,当C/N为7.3~8.4时,好氧生物铁基质载体池DO为2.3~2.7mg/L时,系统氨氮（NH₄⁺-N）、总氮（TN） 、COD和总磷（TP）的平均去除率分别可达90.74%、85.81%、92.65%和95.78%;当进水C/N降至3.3~4.2时,系统NH₄⁺-N、TN、COD和TP的平均去除率仍可维持在81.16%、76.62%、93.87%和94.75%.铁基质生物载体内电解作用显著强化了化粪池内TN的脱除、COD的氧化和TP的固定.氮素转化机制分析表明,内电解与反硝化菌的耦合强化了反硝化作用,降低了反硝化过程对有机碳源的需求,强化了低C/N条件下TN、TP的脱除.     

基于最大熵模型的福建省红树林潜在适生区评估

本研究利用生物气候、地形、底质类型、海温等环境因子和红树林分布数据建立了福建省红树林分布模型,基于最大熵方法分析了福建省沿岸红树林潜在适生区的空间分布.根据模型输出结果对福建省红树林的生境适宜性进行了评估,识别了影响红树林分布的关键环境因子及其适生值区间,并通过空间叠加分析获取了福建省红树林保护与修复的优先区与空缺区域.结果表明,影响福建省红树林适生区分布格局的主要环境因子包括海表温度、气温和降水等,福建省红树林潜在适生区主要位于沙埕港-三沙湾-兴化湾沿岸、泉州湾-厦门湾-九龙江口沿岸、漳江口-东山湾沿岸等地,其中最优适生区面积约为91km².全省共识别出8处红树林保护与修复的优先区域,现存红树林保护率约为64.4%,保护修复空缺主要出现在沙埕港、三沙湾、罗源湾、福清湾等处,研究结论可为未来福建省红树林保护和修复行动提供科学参考.     

典型西南工业城市春冬季PM2.5来源与潜在源区分析——以柳州市为例

为了揭示柳州城区春冬季PM_2.5的来源及其潜在源区分布和贡献,利用2018年24h自动监测数据和气象数据对柳州市大气污染物浓度变化特征进行了分析,并且使用后向轨迹模型（HYSPLIT）对春冬季柳州市PM_2.5逐日72h气流后向轨迹和前向轨迹进行聚类分析,同时结合潜在源贡献因子分析法（WPSCF）和轨迹浓度权重法（WCWT）对其潜在源区和浓度贡献进行了分析.结果显示,（1）在研究期内,不利的主导风向和工业区布局导致研究区PM_2.5在春冬季污染较严重,且工业源和交通源是其主要本地来源;（2）春冬季PM_2.5高值主要来源于西北和东南方向,其中,西北向PM_2.5主要来源于本地排放,且浓度在空间上呈现西高东低的趋势;（3）春季后向轨迹PM_2.5浓度整体大于冬季,春冬季中对柳州市PM_2.5影响最大轨迹均来自东部的短距离输送,而来自西北的气流轨迹输对PM_2.5贡献最低.春冬季柳州市大气PM_2.5通过气流传输对贵州地区大气环境有较大影响;（4）春季,柳州市PM_2.5的主要潜在源区分布在广西东南部、广东中西部、南海沿岸海域、湖南中部、江西西北部、湖北东部及安徽西北部;冬季,主要分布在广西东南部、广东西南部和南海沿岸海域.